Home › Bank capital stack explained

Bank capital stack explained: Pillar 1, Pillar 2A, buffers, MREL and leverage

A bank's capital requirement is a stack: Pillar 1 minimums (4.5% CET1, 6% Tier 1, 8% total capital in the Basel Framework), plus Pillar 2A to make the total capital requirement, plus the combined buffer, plus the PRA buffer. Separate requirements for MREL and the leverage ratio apply alongside it. This page shows the layers in order with the source for each.

Education only. This page explains how published bank capital rules fit together and quotes the sources we read on 19 November 2026. It is not regulatory, legal, investment or financial advice, it does not say what any particular bank must hold or how safe any bank is, and it does not promote any financial product. Where we did not read something it says "not stated". Rules change, so check the current source before relying on a figure.

The layers, bottom to top

  1. Pillar 1. The Basel Framework minimums are 4.5% CET1, 6% Tier 1 and 8% total capital, as a share of risk-weighted assets (RBC20.1; our Basel III minimums page).
  2. Pillar 2A. Firm-specific capital set by the PRA for risks Pillar 1 does not fully capture. Pillar 1 plus Pillar 2A is the total capital requirement (Pillar 2A explained).
  3. Combined buffer. In the PRA's statement of policy it comprises the capital conservation buffer, the countercyclical buffer, the G-SII buffer and, for ring-fenced banks and the largest building societies, the O-SII buffer (capital buffers explained).
  4. PRA buffer (Pillar 2B). An amount held in addition to the total capital requirement and the combined buffer, for a severe stress. The PRA describes the PRA buffer, the combined buffer and the total capital requirement as together making up its capital framework.

Alongside the stack: MREL, which is own funds plus eligible liabilities for resolution, and the leverage ratio requirement, which uses an exposure measure instead of RWA.

Layer by layer

LayerMeasured againstWhat we readSource
Pillar 1RWA4.5% CET1, 6% Tier 1, 8% total capitalRBC20.1
Pillar 2ARWAPart of the total capital requirement; set firm by firm; refined methodology retired from 1 January 2027SoP5/15 ch 9 fn 32; PS2/26
Capital conservation bufferRWA2.5%, CET1RBC30.2
Countercyclical bufferRWA0% to 2.5% in Basel; UK rate 2% (25 September 2026)RBC30.9; FPC record Sept 2026
G-SIB surchargeRWA1.0% to 3.5% by bucket, CET1RBC40.4
PRA bufferRWAAbove TCR and combined buffer; met with CET1; stress-basedSoP5/15 ch 9
MRELRWA or leverage exposureUK G-SIBs: higher of 2 x (P1 + P2A), 6.75% of leverage exposure, 18% of RWABoE MREL SoP para 4.11
Leverage ratioExposure measureBasel 3%; UK 3.25% plus buffersLEV20.7; FPC paper July 2026

System-wide benchmark

The Bank of England's FPC judged in December 2025 that the appropriate benchmark for the system-wide level of Tier 1 capital requirements is around 13% of RWAs, equivalent to a CET1 ratio of around 11%, and reaffirmed it in July 2026. The benchmark excludes firm-specific PRA buffers and requirements set by overseas authorities. The same paper says overall regulatory loss-absorbing capacity is MREL plus buffers. See Bank capital stress tests explained for how stress test results feed in.

Arithmetic illustration (invented numbers)

A hypothetical UK bank with RWA of 1,000 and these requirements, as a share of RWA: Pillar 1 CET1 4.5%, capital conservation buffer 2.5%, countercyclical buffer 2.0%, Pillar 2A CET1 portion 1.0%, PRA buffer 1.5%. CET1 needed to sit above all these layers is 4.5 + 2.5 + 2.0 + 1.0 + 1.5 = 11.5% of RWA, or 115. The Pillar 2A and PRA buffer numbers are invented, and the CET1 share of Pillar 2A is simplified because we did not read the primary rule on it.

Not stated

Frequently asked questions

What is the bank capital stack?

The layers of capital a bank must or should hold: Pillar 1 minimums, Pillar 2A (together the total capital requirement), the combined buffer, and the PRA buffer, with MREL and the leverage ratio applying alongside.

What is the total capital requirement?

In the PRA's framework, total capital requirements are the sum of Pillar 1 capital requirements plus Pillar 2A capital requirements (SoP5/15 chapter 9, footnote 32).

What is in the combined buffer?

The capital conservation buffer, the countercyclical buffer, the G-SII buffer and, for ring-fenced banks and the largest building societies, the O-SII buffer (SoP5/15 chapter 9, footnote 33).

What CET1 ratio is the Bank of England's benchmark?

Around 11%, equivalent to a Tier 1 benchmark of around 13% of risk-weighted assets (FPC, December 2025, reaffirmed July 2026). It excludes firm-specific PRA buffers.

Sources

Documents read on 19 November 2026.

Related guides and calculators